Which CPT codes does my operative note support?
Paste a de-identified operative note into Wonder Bill. Each CPT and ICD-10-CM code the note supports comes back with the sentence behind it, and every code pair and unit count is checked against CMS NCCI edits. You sign or strike each line.
De-identified notes only: the note goes to our server, and an AI model run by the SolvingHealth assistant service drafts the codes. Nothing is billed, filed or sent, and nothing counts as signed until you sign it.
The short answer
A note supports a CPT code when it documents the work that code describes: the procedure, the approach, the side, and anything separately reportable, such as a distinct procedure on a different structure. Then two CMS rules apply to the set:
- Procedure-to-procedure (PTP) edits name code pairs that should not be reported together for the same patient on the same day by the same provider. Each pair carries a modifier indicator: 0 means no modifier allows the pair; 1 means a modifier such as 59 or XS may, when the note documents a distinct service.
- Medically unlikely edits (MUEs) cap the units of one code for one patient on one day.
CMS publishes both tables each quarter, and the NCCI Policy Manual explains the reasoning by CPT chapter. The musculoskeletal chapter covers most orthopedic surgery.
What the check does
- AI drafts each code and quotes the sentence in your note that supports it.
- A deterministic engine, not the AI, grades the drafts against CMS NCCI practitioner edits, 2026 Q4 (v323r0, effective 2026-10-01). The model never grades its own work.
- The engine holds every active CMS edit between 70 codes common in orthopedic surgery. Between two of those codes, no conflict means CMS lists no edit.
- You sign or strike each line, and the receipt shows both.
What it does not do
- A code outside those 70 is marked not checked. It is never shown as passing.
- It does not decide medical necessity, and does not apply commercial payer policies, which can differ from Medicare's.
- It does not bill, file or send a claim. You, or your biller, submit under your own NPI.
- The tables are current through 2026-12-31. After that date the check says its edition is out of date until it is refreshed from CMS.
Planning on a 3D model: 1030T to 1035T
Since July 1, 2026, six Category III codes describe patient-specific digital 3D modeling done before a procedure. They come in three tiers: a model only (1030T, then 1031T for each further 30 minutes), a model with digital simulation such as virtual implant trialing (1032T, then 1033T), and a model with simulation and computational analysis such as finite element analysis (1034T, then 1035T). The base codes need 30, 60 and 90 minutes, added up over 30 days.
- Only the interpreting or supervising physician's time counts. The AMA excludes clinical staff time and the time an interventionalist spends with the model planning the procedure. So the operating surgeon's own planning time is not reported with these codes.
- They are never reported with codes that already include 3D modeling (31627, 75580, 76376, 76377, 0944T), and 1030T and 1031T never with the 3D-printing codes 0559T to 0562T.
- Category III codes have no national Medicare payment amount. Each payer decides.
A clinic's assistant can apply these rules with the rules desk tool modeling_time_check: the tier, the minutes and whose time they were go in; the codes, units and what blocks them come out.
Sources
- CMS, Medicare NCCI Policy Manual
- CMS, Medicare NCCI procedure-to-procedure (PTP) edits
- AMA, CPT Category III long descriptors (1030T-1035T, effective 2026-07-01)
- CMS, Medicare NCCI medically unlikely edits (MUEs)
Checked 2026-11-19. CPT codes and descriptions are copyright of the American Medical Association. Related: revision hip and knee codes, every NCCI pair between these codes, the same checks for agents over MCP.